Eduardo Cano Pleite

Contact Information
Office: 1.1.D16
Phone: +34 91 624 8884
Email: edcanop@ing.uc3m.es”
Position: Teaching assistant

EDUCATION
Eduardo Cano Pleite began a 5-year program in Mechanical Engineering at Madrid’s University Carlos III. From 2010 to 2012 he continued his studies at the Ecole Nationale Supérieure d’Arts et Métiers (ENSAM Paris-Bordeaux) where he obtained his double degree in Mechanical Engineering, collaborating in his FYP with Lille’s Regional Universitary Hospital, and the Master IDI (the Engineer in an International Dimension), with the participation of INSEEC Bussiness School. Back in the University Carlos III, he studied the Master on Industrial Mechanics, in which he obtained the best student record award (2012-2013). His formation continued with a research stay in autumn 2014 at the Kyushu Institute of Technology (Japan), under the supervision of Prof. Yoshihide Mawatari and in summer 2015 at the ETH Zürich (Switzerland) under the supervision of Prof. Christoph Müller. Eduardo obtained his PhD in Mechanical Engineering in December 2016.

RESEARCH INTERESTS
Eduardo’s interests are mainly focused on CFD simulations of vibrated fluidized bed, studying its perfomance and comparing its results with experimental data.

TEACHING ACTIVITIES
Laboratory lessons of thermal engineering (CFD) for undergraduate students.

PUBLICATIONS

Journal publications

Reversal of gulf stream circulation in a vertically vibrated triangular fluidized bed
Powder Technology. 2017.
E. Cano-Pleite, F. Hernández-Jiménez, A. Acosta-Iborra, C.R. Müller

Segregation of equal-sized particles of different densities in a vertically vibrated fluidized bed
Powder Technology. 2017.
E. Cano-Pleite, F. Hernández-Jiménez, A. Acosta-Iborra, T. Tsuji, C.R. Müller

Bulk oscillation and velocity wave propagation in a vibrated fluidized bed at minimum fluidization conditions
Powder Technology, 308, 346-361. 2017.
E. Cano-Pleite, F. Hernández-Jiménez, A. Acosta-Iborra.

Oscillatory behavior of the bed bulk and the bubbles in a vertically vibrated pseudo-2D bed in bubbling regime
Chemical Engineering Journal, 312, 228–242.. 2017
E. Cano-Pleite, F. Hernández-Jiménez, A. Acosta-Iborra, Y. Mawatari


Effect of vertical vibration and particle size on the solids hold-up and mean bubble behavior in a pseudo-2D fluidized bed

Chemical Engineering Journal, 304, 384–398, 2016.
E. Cano-Pleite, Y. Shimizu, A. Acosta-Iborra, Y. Mawatari.

Development of an empirical wall-friction model for 2D simulations of pseudo-2D bubbling fluidized beds
Advanced Powder Technology 27 521-530. 2016.
F. Hernández-Jiménez, J. Sánchez-Prieto, E. Cano-Pleite, L.M. Garcia-Gutierrez, A. Acosta-Iborra.

Compressible-gas two-fluid modeling of isolated bubbles in a vertically vibrated fluidized bed and comparison with experiments
Chemical Engineering Journal 271 287-299. 2015.
E. Cano-Pleite, F. Hernández-Jiménez, A. Acosta-Iborra.

Experimental study on the motion of isolated bubbles in a vertically vibrated fluidized bed
Chemical Engineering Journal 255 114-125. 2014.
E. Cano-Pleite, F. Hernández-Jiménez, M. de Vega, A. Acosta-Iborra.

Characterisation of the particle-wall frictional forces in pseudo-2D fluidized beds using DEM
Chemical Engineering Science 106 136-143. 2014.
F. Hernández-Jiménez, T. Li, E. Cano-Pleite, W. Rogers, A. Acosta-Iborra.

Conference proceedings

Characterization of the bubble behavior in vibrated fluidized beds by means of two-fluid CFD simulations coupled with accelerometry data
The 14th International Conference on Fluidization – From Fundamental to Products, 2013.
E. Cano-Pleite, J. Gómez-Hernández, J. Sánchez-Prieto, A. Acosta-Iborra.